Navman 4433 Instrukcja Użytkownika

www.navman.comPilot 3380AUTOPILOTwww.navman.comFish 4432 / 4433FISHFINDERSInstallation and Operation Manual

Scroll speedUse this to set the scroll speed on the display. There is a choice of: Very Fast, Fast, Medium, Slow and Pause. The depth of the water al

It is essential to do this whenever some fuel is added or removed. Otherwise, the reading on the Fuel display (see section 5-6 Fuel Display) and the

Press MENU one or more times until the Setup menu is displayed, then select Alarms:Trigger settings can be defined to suit the boat and individual pre

Press MENU once or more until the Setup menu is displayed, then select Calibrate: The fuel options can be calibrated only when the optional single o

TemperatureThe factory settings should be sufficiently accurate for normal usage. To calibrate the temperature readout, first measure the water temper

4-1 Interpreting the displayThe sonar displays do not show a fixed distance travelled by the boat; rather, they display a history, showing what has pa

ShadowsShadows are created around areas where the ultrasonic beam cannot ‘see’. These areas include hollows on the bottom or beside rocks and ledges,

When to use 200 kHzThe 200 kHz frequency is best for seeing deep bottoms, showing detail and reducing noise.When to use 83 kHzThe 83 kHz frequency is

83 kHz displayDual screen200 kHz display200/83 Khz displayNote the wider bottom traceNote the smaller, defined fish arches and more bottom detail.FISH

4-3 Fish detection and displayWhere to find fishUnderwater features like reefs, wrecks and rocky outcrops attract fish. Use the 83/200 kHz frequency d

Contents1 Introduction ...

Unwanted signalGain Threshold line4-4 GainGain (sensitivity) controls the amount of detail displayed on the FISH 4432/4433. Understanding how to set s

4-5 RangeRange is the vertical depth displayed on the FISH 4432/4433. The Navman fishfinder has two range modes, Auto Range and Manual Range:• In Aut

Note: Refer to Section 3-2 Setup > Sonar, for information about customizing features on the sonar displays.Sonar display at a single or mixed freq

To customize the size of the Data header, highlight Size and press ENT. There is a choice of Small and Large.To customize the data items to be display

5-4 Sonar 83/200 displayTo show the Sonar 83/200 display, press DISP and select Sonar Tab, select Sonar 83/200 and press ENT.This shows a split disp

To show the Fuel display, press DISP and select Other Tab, select Fuel and press ENT.There are no options. (See section 3-3 Setup > Fuel for inform

5-9 About displayTo show the About display, press DISP, select Other Tab, select About and press ENT.There are no options.This shows the fishfinder

Correct installation is critical to the performance of the FISH 4432/4433. There are two components to install, the display unit and 6 Installation an

Green Wire: Use this to connect a secondary alarm indicator such as a flashing light or external beeper with a built-in drive circuit. See the Auto po

6-1 What comes with this product?Standard configuration:• FISH 4432/4433 display unit• Power cable• Mounting bracket (screws included)• Warranty r

6-3 Mounting and removing the display unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306-4 Systems of several in

Removing the display unitThe display unit can be removed after each use for protection against the environment or security reasons.When removing the d

6-5 Cleaning and maintenanceTo avoid damage, clean the screen only with a damp cloth and mild detergent when dirty or covered in sea salt. Avoid abras

Specifications FISH 4432 FISH 4433Display type: 16 GreyscalesScreen Resolution 360 high x 240 wide(pixels)White LED backlightingDisplay size: 4.3”

This troubleshooting guide is written with the assumption that the user has read and understood the relevant sections in this manual.It is possible in

2. The fishfinder won’t turn off: The fishfinder may have been wired for Auto power. In this case, the fishfinder cannot be turned off while the ign

7. If the fishfinder beeps when turned on but nothing is displayed: The fishfinder may be operating, but the backlight settings may have been set t

How to contact us www.navman.comNORTH AMERICABNT - Marine Electronics30 Sudbury Rd, Acton, MA 01720.Toll Free: +1 866 628 6261Fax: +1 978 897 8

Lon 174° 44.535’ELat 36° 48.404’SMade in New ZealandMN000433BFISH 4432 / 4433

Congratulations on choosing a Navman fish-finder. For maximum benefit, please read this manual carefully before installation and use. This manual desc

1-2 How the FISH 4432/4433 worksThe FISH 4432/4433 has two parts:- the transducer attached to the hull- the display unit.The transducer generates an u

Power On / Auto PowerPress to turn the fishfinder on.If the fishfinder is wired for auto power, it turns on automatically whenever the boat’s igniti

3 Setting up the FISH 4432/4433Press MENU twice, to show the Setup menu, then select a particular option using the or cursor keys. (Section 2 Basic

The Setup menu and optionsSonar - see section 3-2Simulate - see section 2Comms - see section 3-7Alarms - see section 3-5Fuel - see section 3-3Logs - s

Press MENU once or more until the Setup menu is displayed, then select System: LanguageSelect the language for the displays. The options are: English